#12 Knife does not fit my grinder
-
Customer service is taking care of me already but I wanted to see if anyone else is having or have had this issue. I have a 10 year old #12 cabelas grinder. I ordered the #12 Everlasting knife from Walton’s. When I got it it does not fit on the auger. It’s too small. Does cabelas have a unique size or is this a fluke on the Everlasting knife? I bought a new cabelas #12 knife and it says “fits all #12 grinders” which leads me to believe they do not have a unique size.
-
@BrianB When you say its too small, do you mean that the center auger is too big and that the square hole in the knife won’t make it over that, or vice versa?
-
@Jonathon correct. The square on the knife is too small.
-
-
@BrianB I just bought the #32 butcher series and bought Everlast knifes so each plate could marry. However the Everlast knife is to thick and doesn’t let plate engage the notch. Weston knife allows it to sit deeper but not much better. I’m still waiting for a solution or some direction from customer service.
-
-
-
@iowa-arborist I use the exact same setup, an everlast knife and a weston plate and I have no problems at all. What Weston grinder do you have?
-
Here’s my #22 with everlasting knife and regular plate
-
@Jonathon I have the #32 butcher series. It’s seated fully into the bushing at the rear also. Tho there does seem to be a bit of slop in the bushing.
-
@Jonathon I took a measurement of the weston and everlasting knife and there appears to be about a 2.5mm difference in thickness. You think I could surface grind the back of knife or just sharpen the blades down aways as a solution? I realize that would kinda defeat the purpose of purchasing knives you can sharpen but unsure how to solve this.
-
-
This post is deleted!
-
-
@iowa-arborist that is a big difference.
-
@Jonathon I mailed it back yesterday. You should try to catch it and see if there are any discrepancies from other #12’s. It would be nice to see if there is a consistency issue and nail it down so there’s do not lose money sending it back. If you need any numbers I can mic my auger. I sent it back attn: RMA 3740 if that helps.
-
@BrianB I think so as well. I’m kinda waiting to hear back on how I should proceed
-
@BrianB I will ask that it be brought to me when it comes in.
-
@BrianB @iowa-arborist This arrived yesterday and I had the time to do some checking this morning and it does NOT work with a Weston #12 Butcher or Pro Series Grinder. I have updated the website to include that information and am very sorry, the #22 everlasting knife works perfectly with the #22 Pro Series Grinder, so I have no clue why this would be different with a #12.
I also tried a few other knives to make sure that it wasn’t just this particular one and it is all of them that have a problem.
-
@Jonathon I have the butcher series #32 so do they just not fit any of the butcher series then? Mine goes on fine its just to thick to let the plate fit correctly
-
@Jonathon that is a bummer as I was looking forward to having a good knife. I am glad the issue will be resolved going forward.
-
@iowa-arborist I just checked against a #32 butcher series grinder and it DOESN’T work. I dont have a #32 pro to compare it to but I can say it absolutely works on the #22 Pro Series.
-
@iowa-arborist and I am now questioning this. I might be using the Value Hard Grinder. I am going to do some testing and I will update
-
@iowa-arborist and anyone else, I was right the #22 pro works with the everlast and the Value Hard Knife.
-
@Jonathon
What about the #22 butcher series?
-
Argh, I dont have one to test right now but I believe that they will. Once we get a butcher series back in stock I will test it right away.
-
This is odd. Everlasting knife vs value hard knife. After one grind and wash the value hard showed immediate signs of rust. Must be the metal composition. Even worse two days later. Both were sprayed with silicon after drying. It did cut very nicely but…
-
I bought some knives years ago for my thunderbird #12 grinder and they were too thick and would not let the auger turn, I never got around to grinding the sholders off to let them work. I am contemplating purchasing a #32 butcher series hopefully they get the issue resolved.
-
@PapaSop I’ve seen that on the back edge of the knife but never on the leading edge. Hitting it with silicon will do the trick.
-
@PapaSop that’s because the blades of the Value hard are brazed onto cheap casting. The Everlasting is cast and machined out of one piece of steel.
-
@johnsbrewhouse
Thanks for the info. Everlasting going forward.
Recent Posts
-
@dwilk1 There are more factors than just the temperature when it comes to emulsification, though that certainly is one of them! What protein are you using? Is it straight beef, straight pork, a mix of the two? Just FYI I am visiting some meat processing plants tomorrow so I will do my best to respond but it might not be until Friday.
Recent Topics
Popular Topics
